Conduit & Fittings

Meets the requirements of NEC® Section 300.4(E), Supports conduit or pipe 1-1/2" (38 mm) under the roof decking to prevent potential damage from nails or screws. Roof Decking Sheet Thickness: 24 GA Min, 2" Max Trapeze Width

* List Price is for Whole Pack of 50 Pieces

Fastens cables to top of flange， Requires only a hammer to install

* List Price is for Whole Pack of 100 Pieces

Supports conduit/pipe or cable from beam flanges, Snap close clip pivots a full 360°, Static Load: 25 lb

* List Price is for Whole Pack of 100 Pieces

Snap Close Conduit to Rod/Wire Clip, 1/2", 3/4" EMT, 0.71"–1.18" Outer Diameter, 1/2", 5/8" Rod

* List Price is for Whole Pack of 100 Pieces

One piece break apart strut clamp for EMT and Rigid conduit, Includes thread impression and captured screw. 0.710" – 0.840" Outer Diameter, Static Load 200 lb

* List Price is for Whole Pack of 100 Pieces

Fix pipe or conduit parallel to a beam.

* List Price is for Whole Pack of 25 Pieces

Requires only a hammer to install, Available for EMT, rigid, IMT and aluminum conduit, Will pivot thru 360°, Ultimate Static Load: 25 lb

* List Price is for Whole Pack of 100 Pieces

One assembly provides support for electrical box and/or conduit from beam flanges, Comes with one conduit clip attached to each side with the ability to attach up to two more per side

* List Price is for Whole Pack of 25 Pieces

Neatly isolates, supports and secures MC/AC cables, Properly spaces MC/AC cable to help eliminate bundling and NEC® & CEC derating issues, Results in a "neat and workmanlike" installation. 0.430" – 0.560" Outer Diameter, 10-2 Super Neutral

* List Price is for Whole Pack of 25 Pieces

One piece break apart strut clamp for EMT and Rigid conduit, Includes thread impression and captured screw. 1.510" – 1.660" Outer Diameter, Static Load 200 lb

* List Price is for Whole Pack of 50 Pieces

Snap Close Conduit to Rod/Wire Clip, 1/2", 3/4" EMT, 0.71"–1.18" Outer Diameter, 3/8" Rod

* List Price is for Whole Pack of 100 Pieces

One assembly provides support for electrical box and/or conduit, Comes with one conduit clip attached to each side with the ability to attach up to two more per side, Eliminates need for offset bending conduit, 66% less Drop Wires (rod/wire application)

* List Price is for Whole Pack of 25 Pieces

Clip snaps on flange and cable snaps into clip.

* List Price is for Whole Pack of 100 Pieces

Push-in installation of conduit, Eliminates need for offset bending conduit, Complete with shot-fire bracket and pre-assembled drive pin from DEWALT®, Quickly and easily attaches to concrete, steel or composite metal decking, Integrated pin installs easily using powder-actuated or single-shot gas-actuated tools, Ultimate Static Load: 15 lb

* List Price is for Whole Pack of 50 Pieces

Supports conduit to rod, wire or flange,Can also be used for flexible metallic tubing, armored cable, portable cables, control tubes and communications cable,Available for EMT, rigid, ENT, IMT, MC/AC and aluminum conduit,No installation tools required

* List Price is for Whole Pack of 100 Pieces

May be used for either vertical or horizontal installations, Static Load 1: 100 lb, Static Load 2: 25 lb

* List Price is for Whole Pack of 100 Pieces

MC/AC Cable to Rod/Wire Clip, 1/4" Rod, #12 Wire, 14-2 to 10-3 MC/AC, 1/4";5/16";3/8" Rod Size

* List Price is for Whole Pack of 100 Pieces

Clip snaps on flange and cable snaps into clip.

* List Price is for Whole Pack of 100 Pieces

One-piece cable/conduit clamp with protective boot, No screws or bolts to drop, Requires only a screwdriver or nutdriver for installation, Fits into open side of strut channel, FM® Specification Tested (from 1/2" to 4" of EMT Conduit Size). Static Load 1 350 lb, Ultimate Static Load 2 75 lb, Ultimate Static Load 3 50 lb

* List Price is for Whole Pack of 50 Pieces