Electrical

• Used as primary insulation for wire and cable splices up to 600 volts
• Used for wire harnessing, jacketing on high voltage splices
• Superior adhesion and elasticity, excellent tensile strength
• Highly resistant to UV, abrasion and corrosion, flame-retardant

WW-EF is a 0.125in. (3.2mm) self-amalgamating mastic for insulating and sealing all types of overhead and direct buried electrical connections up to 600 volts. WWEF has superior adhesion to metals, cable insulations and jackets. It will have no adverse effects on polymeric conducting shields. WW-EF is normally wrapped with vinyl tape.

WW-RSL is a 30 mil (0.76mm) self-amalgamating, low voltage rubber tape which is UL-510 Listed for use as primary insulation at not more than 600 volts. It easily conforms to irregular shapes and surfaces yielding a void free electrically stable build-up. WW-RSL is compatible with all extruded dielectric cable insulations. Meet ASTM D-4388 type I standard.

Techspan 669972B - Wrap ‘N’ Seal Automotive Tape (Self-Fusing) - 22FT x 0.750" x 0.030" - Black - 50 Rolls/Carton

Techspan 769999B - PVC Electrical Tape - 60' x 3/4" x 0.007" - Black - 100 Rolls/Sleeve

WW-MSR is a 125 mil (3.2mm) self-amalgamating, insulating mastic for insulating and sealing all types of overhead and direct buried electrical connections up to 600 volts. For water sealing ductwork, cable ends and all types of splices. Normally WW-MSR should be jacketed with vinyl tape.

Techspan 669999 - PVC Electrical Tape - 60' x 3/4" x 0.007" - Black - 1 Roll

WW-CP-202P is a printed, 20 mil, plasticized PVC tape with superior adhesion and corrosion protection. This tape can be used to protect against abrasion, corrosion, and impact on metal pipes, conduit, and fittings. It is suitable for use above and below ground.

• Used as primary insulation for wire and cable splices up to 600 volts
• Used for wire harnessing, jacketing on high voltage splices
• Superior adhesion and elasticity
• Highly resistant to UV, abrasion and corrosion, flame-retardant

WW-HR is an ethylene rubber based high voltage tape with excellent electrical, chemical and physical properties. WW-HR is a linerless, self-bonding tape that permits much quicker taping speeds than a tape with a liner and yields a uniform, void-free build-up. WW-HR is compatible with all extruded cable insulations and is specially formulated to have excellent thermal conductivity that will allow the heat to dissipate from a joint.

An ethylene rubber based, high voltage tape possessing excellent electrical, chemical and physical properties. Use linerless, self-bonding tapes when insulating and jacketing splices on power cable from 600 volts to 69,000 volts. Allows quicker taping speeds than liner tape and yields a uniform, void-free build-up while contouring unusual shapes.

• Good adhesion and elasticity
• All weather performance
• Great tensile strength
• Resistant to UV, abrasion and corrosion
• Flame-retardant

List price is for whole pack of 10 pieces.

WW-CP-201P is a prinited,10 mil plasticized PVC tape with superior adhesion and corrosion protection. This tape can be used to protect against abrasion, corrosion, and impact on metal pipes, conduit, and fittings. It is suitable for use above and below ground.

WW-SC is an ethylene propylene rubber based, self-amalgamating and conducting tape. Its unsupported construction makes it ideal for use on power cable where accomodation of expansion and contraction due to load cycling is important. WW-SC is compatible with all extruded dielectric cable insulations. Meets ASTM D-4388 Type IV standard.

• Forms a tough, flexible coating on metal, rubber and plastic to help waterproof connections
• Quick drying formula
• Excellent for hard to tape places
• Absorbs vibrations which prevents terminal screws from loosening
• Stays clean and neat
• Will not crack or unravel
• Can also be used as a thread locker or gasket sealer
• Applicator brush included
• Can be used in automotive, marine, heavy-duty, RV, industrial and  electrical applications
• 118mL (4 fl oz.) can

• 600 Volt rating
• Flame Retardant
• Weather-Resistant
• Can be used as primary insulation at not more than 600 Volts
• Lead-free • Temperature rating: -18°C to 105°C (0°F to 221°F)
• Easily applied at low temperatures • Highly elastic
• Dimensions (Length x Width x Thickness): 20m x 19mm x .18mm (66' x 3/4" x .007")
• CSA Approved/UL Listed