Skip to Main Content »

Search Site
Your shopping cart is empty

All Prices are in Canadian Dollars

Lithonia Lighting WF4 LED 27K MW M6 - 4" Wafer-thin LED Downlight - 10.6W - 120V - 2700K Warm White - 80 CRI - 660 Lumens - Matte white

Be the first to review this product

Lithonia Lighting WF4 LED 27K MW M6 - 4" Wafer-thin LED Downlight - 10.6W - 120V - 2700K Warm White - 80 CRI - 660 Lumens - Matte white

  Energy Star Dimmable

Availability: In stock


Lithonia Lighting WF4 LED 27K MW M6 - 4" Wafer-thin LED Downlight - 10.6W - 120V - 2700K Warm White - 80 CRI - 660 Lumens - Matte white

Double click on above image to view full picture

Zoom Out
Zoom In

More Views

Additional Information

Brochures & Specific Sheets

Stock Code WF4 LED 27K MW M6
Brand Lithonia Lighting
Fixture Type Indoor/Outdoor
Voltage (V) 120V
Wattage (w) 10.6 W
Bulb Type LED
Lumens (Initial) 660 lumens
CRI 80
Color Temperature (K) 2700K Warm White
Height (in) 1.1''
Finish Matte white
Dimmable Yes
Lens: Polycarbonate
Mounting Recessed
UPC 191723446289
Start Temp. (Min) -40°C
Start Temp. (Max) 40°C
Type Downlight
Life Hours 36,000 hours
UL Listed CSA Listed
Warranty 5-year limited warranty


4" LED Module


INTENDED USE — The 4" Wafer-Thin LED recessed downlight with remote driver box combines high quality light output and efficiency while eliminating the pot light housing for competitive affordability. This innovative wafer-slim Type IC design allows easy installation for new construction or remodel from below the ceiling without the requirement of a pot light housing. The LED module maintains at least 70% light output for 36,000 hours. These LED Wafer downlights are intended for closets, attics, hallways, bathrooms, kitchens, basements, soffits, entry ways, porches, garages, stairwells, corridors, nursing/retirement homes, condos, elevators, apartments, and any other small areas.

CONSTRUCTION — IC rated driver and fixture - approved for direct contact with insulation. Aluminum die cast outer frame. Durable, powder coat paint to prevent rust. Round fixture with integral edge-lit LED's. Plenum rated cable connector to connect from module to remote driver box. Isolated driver integrated inside steel remote box with four 7/8" knockouts with slots for pryout. Suitable for pulling wires with the 12 cubic-inch wiring compartment to accommodate up to (8) 14 gauge insulated conductors, or (6) 12 gauge insulated conductors; making the Wafer LED Downlights much easier to wire in 2in/2out (plus ground) daisy-chain applications and contractor friendly.


INSTALLATION — Ideal for shallow ceiling plenum; no housing required. Steel spring clip for easy installation. 4" cut out template is provided to ensure a correct sized hole is cut into ceiling for proper installation of the trim. Size of hole should not exceed 4 1/4 inches for this product. Suitable for installation in t-grid and drop ceiling applications. 3" plenum space required for installation of the remote driver box.

OPTICS — Wafer-Thin downlight edge-lit LED technology uses light guided plate to distribute light. Polycarbonate lens provides even illumination throughout the space. Utilizes 2700K, 3000K, 3500K, 4000K, and 5000K color temperature LEDs.

ELECTRICAL — Connect directly to 120V power supply via provided UL recognized driver. High efficient driver with power factor > 0.9. Ambient operating temperature: -40°F (-40°C) to +104°F (+40°C). Dimming down to 10% (See page 2 for recommended dimmers). Standard input wattage is 9.6W, 70 lumens per watt. Replaces 50W incandescent.

LISTINGS — CSA certified to US and Canadian safety standards. ENERGY STAR® certified. Wet location. Air Tight certified in accordance with ASTM E283-2004. NOM Certified.

WARRANTY — 5-year limited warranty.

Note: Actual performance may differ as a result of end-user environment and application.

All values are design or typical values, measured under laboratory conditions at 25 °C.

Specifications subject to change without notice.

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.